# # this config file was automatically generated # using lirc-0.8.1-CVS-pvr150(udp) on Fri Apr 6 17:00:41 2007 # # contributed by John Lofgren # # brand: Zenith # model no. of remote control: ZN5015 # The ZN5015 is a universal remote. This config file is setup using code 838 - # one of the two listed Tivo remote codes. After trying a few codes, this code # worked with the most buttons on the remotes and gave few redundancies in the # key codes. Note the # devices being controlled by this remote: mythtv frontend/backend # # NOTES: # The ZN5015 is a cheap universal remote. This config file is set up using code # 838 - one of the two listed Tivo remote codes. After trying a few codes, this # code worked with the most buttons on the remote and gave few redundancies in # the key codes. Note the following: # -To set the remote code: # 1. Hold down CODE SEARCH for a couple seconds until the LED stays on. # 2. Press one of the four source device buttons: VCR, SAT, CBL, or DVD. # (Do not choose TV - this button can only be used for TV codes.) # Note, you can set a different code for each of the source buttons. # 3. Type in the three digit code (8, 3, 8). The LED should turn off if # you were successful. # -The SHIFT key is not very friendly. It is a pain-in-the-you-know-what. But, # as they say, it is best to know thy enemy. The SHIFT key is used to activate # the green-colored functions on several keys # When SHIFT is pressed once, the LED turns on. Press it again to turn SHIFT # off. When SHIFT is on, the code for # the green function of the button will be output. When SHIFT is off, the # code for the other function on the key will be sent. For example, when you # press the UP / CHAN+ key, if SHIFT is on, the code for UP will be sent. If # SHIFT is off, the code for CHAN+ will be sent. Make sure SHIFT is off when # pressing buttons without a green function. These buttons may produce no code # or a code for a different button while SHIFT is on. # -The following keys control the remote itself and are not meant to output IR # codes: TV, VCR, SAT, CBL, DVD, CODE SEARCH, SLEEP, SHIFT # -The volume up, down, and mute keys do not work with code 838. # -The GUIDE and INFO keys produce the same output with code 838. # -The PREV CHAN/REPEAT and ENT(er) keys produce the same output with code 838. # -The CC (closed caption)/SUBTITLE and INPUT/TV-VCR keys produce the same # output with code 838. # begin remote name Zenith_ZN5015_CODE838 bits 12 flags SPACE_ENC eps 30 aeps 100 header 2478 503 one 1278 501 zero 666 501 post_data_bits 8 post_data 0x59 gap 13260 min_repeat 2 toggle_bit 0 begin codes KEY_POWER 0xA8B # Was: power KEY_CHANNELUP 0x08B # Was: chan_up KEY_CHANNELDOWN 0x88B # Was: chan_down KEY_UP 0xFAB # Was: up KEY_DOWN 0x06B # Was: down KEY_LEFT 0x46B # Was: left KEY_RIGHT 0x86B # Was: right KEY_OK 0x7AB # Was: ok KEY_MENU 0xF6B # Was: menu KEY_QUIT 0xC6B # Was: quit KEY_INFO 0xD4B # Was: info KEY_INFO 0xD4B # Was: guide KEY_CLOSE 0xCEB # Was: closed_caption prev_chan 0xD0B KEY_1 0x00B # Was: one KEY_2 0x80B # Was: two KEY_3 0x40B # Was: three KEY_4 0xC0B # Was: four KEY_5 0x20B # Was: five KEY_6 0xA0B # Was: six KEY_7 0x60B # Was: seven KEY_8 0xE0B # Was: eight KEY_9 0x10B # Was: nine KEY_0 0x90B # Was: zero KEY_ENTER 0xD0B # Was: enter input 0xCEB KEY_REWIND 0xD8B # Was: rew KEY_PLAY 0x58B # Was: play KEY_FASTFORWARD 0x38B # Was: ff KEY_RECORD 0xB8B # Was: rec KEY_STOP 0xC4B # Was: stop KEY_PAUSE 0x98B # Was: pause end codes end remote